DPMS and DDC are trademarks of VESA.Į NERGY S TAR ® is a registered trademark of the U.S. VESA is a registered trademark of the Video Electronics Standards Association. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation.
#Vx910 viewsonic drivers windows#
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc. Service is required when the unit has been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.Ĭopyright © ViewSonic ® Corporation, 2005. Refer all servicing to qualified service personnel. Unplug this equipment when it will be unused for long periods of time.ġ4. When a cart is used, use caution when moving the cart/ equipment combination to avoid injury from tipping over.ġ3. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the equipment. Only use attachments/accessories specified by the manufacturer.ġ2. Be sure that the power outlet is located near the equipment so that it is easily accessible.ġ1.
Protect the power cord from being tread upon or pinched, particularly at the plug, and the point where if emerges from the equipment. If the plug does not fit into your outlet, consult an electrician for replacement of the outlet.ġ0. The wide blade and the third prong are provided for your safety. A grounding type plug has two blades and a third grounding prong. A polarized plug has two blades with one wider than the other. Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug.
#Vx910 viewsonic drivers install#
Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat.ĩ. Install the equipment in accordance with the manufacturer’s instructions.Ĩ. If further cleaning is required, see “Cleaning the Display” in this guide for further instructions.ħ. Keep these instructions in a safe place.Ħ. Read these instructions completely before using the equipment.Ģ. Notice: Use the cables which are included with the unit or specified.ġ. The device complies with the requirements of the EEC directive 89/336/EEC as amended by 92/31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic compatibility,” and 73/23/EEC as amended by 93/68/EEC Art.13 with regard to “Safety.” This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.Ĭet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Also, any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. To assure continued FCC compliance, the user must use grounded power supply cord and the cables which are included with the equipment or specified. Consult the dealer or an experienced radio/TV technician for help.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Increase the separation between the equipment and receiver.Reorient or relocate the receiving antenna.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: However, there is no guarantee that interference will not occur in a particular installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. OSD and Power Lock Settings.Īdjusting the Screen Image. Important Safety Instructions.Ĭopyright Information.
0 kommentar(er)
